Plumbing Basics: Your Key to Installing a Bathtub
Plumbing Basics: Your Key to Installing a Bathtub
Blog Article
Just about every person seems to have their unique opinion when it comes to A Step-by-Step Guide to Installing a Bathtub.
Installing a bath tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old tub with a new one is likewise a reasonably tough project. If the old bathtub is conveniently easily accessible, the task can move immediately; if you have to open a wall to get rid of the old bathtub and position the new bath tub, the job is a lot harder. In either case, the project is within a house handyman's abilities, although you will certainly require an assistant to vacate the old bathtub and also set in the new one. Make sure you have qualified yourself for the job and are comfortable attempting it. Rather than working with a contractor to take over a halfway-completed project, it is far better to consider using one before you start. Chances are you may need an expert plumber to make tube links.
This post will certainly help you mount a new tub in your shower room if you have already bought a new bathtub as well as do not require to change the setup of your previous water system pipes.
Your devices as well as material list should comprise the following:
Removing Old Taps
If you require to replace old faucets with new ones as a part of your installation, after that the first thing you must do is detach the water. After doing so, switch on the taps to drain pipes any kind of water staying in the system. The process of getting rid of the existing taps can be rather bothersome due to the limited accessibility that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipelines to the faucets. Have a fabric prepared for the staying water that will originate from the pipes. When the supply pipes have been gotten rid of, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single faucets from turning throughout this process. When the faucets have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned up of any type of old securing substance.
Prior to proceeding to fit the brand-new faucets, compare the pipe connections on the old taps to the new faucets. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new taps are plastic, after that you will require a plastic connector to prevent damages to the string. One end of the port fits on the plastic tail of the faucet as well as the various other end provides a link to the existent supply pipelines.
If you need to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipe.
Next off, position the faucet in the placing opening in the bath/basin making sure that the washing machines remain in location in between the tap and also the sink. Secure the tap in position with the manufacturer offered backnut. When the faucet is firmly in position, the supply pipelines can be connected to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with typical tap adapters. The former kind should be attached to the faucet finishes initially, tightening up just by hand. The supply pipes can later be attached to the various other end. Tighten up both ends with a spanner after both ends have been connected.
Installing the Bath tub
Utilizing the two wooden boards under its feet, put the bathtub in the needed setting. The wood boards are practical in evenly spreading the weight of the bath tub over the area of the boards rather than focusing all the weight onto 4 small factors.
The next goal is to ensure that the tub is leveled all round. This can be accomplished by examining the level and changing the feet on the bath tub till the spirit level checks out level.
To set up faucets, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression join; after that do the exact same for the various other faucet.
Switch on the water system and inspect all joints as well as brand-new pipework for leakages as well as tighten them if essential. Fill up the tub and also check the overflow outlet as well as the normal outlet for leaks.
Lastly, take care of the bathroom paneling as explained in the maker's instruction manual. Tiling and securing around the tub ought to wait until the bath tub has actually been used at the very least when as this will certainly settle it right into its last setting.
Planning for the Setup
Firstly, the sustaining framework supplied with the bathroom must be fitted (if called for) according to the supplier's instructions. Next, fit the faucets or mixer to the tub. When suitable the faucet block, it is essential to make certain that if the tap features a plastic washing machine, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is likewise practical to fit a supporting plate under the taps device to stop pressure on the tub.
Fit the flexible faucet ports to the bottom of the two faucets using 2 nuts and also olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the outlet via the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the flexible overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which must be fitted inside the bathroom. See to it you utilize all of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath should currently be ready to be suited its final position.
Tiling Around the Tub
In the area where the bathroom meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is very important as the fitting can relocate enough to fracture a rigid seal, creating the water to penetrate the wall surface between the bathroom and also the tiling, causing complications with wetness and possible leaks to the ceiling listed below.
You can choose from a range of coloured sealers to assimilate your fixtures as well as installations. They are sold in tubes as well as cartridges, as well as can securing spaces approximately a size of 3mm (1/8 inch). If you have a bigger space to fill up, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly load the bath tub with water prior to securing, to enable the movement experienced when the tub is in use. The sealant can break relatively very early if you do not consider this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily offered on the marketplace. It is recommended to fit the ceramic tiles making use of water-resistant or water-proof sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Do you appreciate reading up on How to Install a Bathtub Yourself? Create a remark down below. We'd be delighted to see your ideas about this blog posting. Hoping that you come back again in the near future. In case you enjoyed reading our page plz make sure you remember to share it. We enjoy reading our article about How to Install a Bathtub.
Source This Article Report this page